Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateTrusted Garage Door Spring Repair for Bloomington Homeowners
A broken garage door spring stops your day cold. The door won’t lift, or it slams down hard enough to shake the frame, and suddenly the car is trapped inside. We handle Bloomington garage door repair calls like this every week, and spring replacement is our most common job.
Our technicians have up to 10 years of experience with high-tension spring work, the repair most general handymen turn down because of the injury risk. We service Genie, Clopay, Amarr, and Wayne Dalton equipment, so you won’t need a second specialist for a different make. Fast dispatch runs from 7am to 7pm, Sunday through Friday, and same-day repair is often possible in Bloomington. Call (855) 904-7314 and we’ll get you back up and running the same day.
What Our Garage Door Spring Repair Service Includes
Every spring job starts with a full inspection of the spring system, cables, drums, and hinges before we touch anything. Here’s what the work covers.
Torsion Spring Replacement
Torsion springs mount on a steel shaft above the door and do the heavy lifting through a winding cycle, and when one snaps you usually hear a loud bang from the garage. You need replacement when the door feels dead weight, opens a few inches and stops, or the spring shows a visible gap in the coil. We measure the old spring’s wire gauge, inside diameter, and length, then install a matched replacement wound to the correct tension for your door’s weight. A torsion spring is often replaced as a pair, since both springs wear at the same rate.

Extension Spring Replacement
Extension springs run along the horizontal tracks on each side of the door and stretch as the door closes. They’re common on older Bloomington doors and on lighter single-car models, and they fail by stretching out, losing tension, or breaking outright. We replace them with the correct weight rating for your door and fit safety cables through the center of each spring so a break can’t send the spring across the garage.

Broken Spring Repair
A snapped spring is the single most common spring call we get, and it almost always happens with the door in the closed position. The door becomes too heavy to lift by hand and the opener strains or refuses to run. We confirm the break, check that nothing else was damaged when it let go, and replace the failed spring so the door balances again.

Spring Adjustment
Sometimes the spring isn’t broken, just out of tune. A door that drifts down on its own, feels heavier than it used to, or won’t stay open halfway is telling you the tension is off. We check the balance point and adjust the winding to bring the door back to neutral, which takes strain off the opener and quiets the whole system.
Safety Cable Installation
Safety cables are the thin steel cables that thread through extension springs to contain them if they break. Many older doors were built without them, and that’s a real hazard in a garage where people walk under the door. We fit cables rated for the spring load and anchor them properly at both ends.
Spring Inspection
A spring can be close to failing long before it breaks, and a quick inspection catches the warning signs early. We look for rust, coil gaps, stretched extension springs, and uneven wear between a pair. If your door is more than a few years old and you’ve never had the springs checked, an inspection is cheap insurance against a morning breakdown.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Brands We Service for Garage Door Spring Repair
We work on Genie and Clopay systems regularly, and we know where each one tends to wear. Genie door hardware shows up on a lot of older Bloomington homes, and its spring and cable setups have quirks worth knowing before you start winding. Clopay doors are common on newer builds, and matching the right spring to the door’s rated weight matters more on those models because the panels are heavier.
We also service Amarr and Wayne Dalton equipment, including doors where the spring system is integrated with a proprietary track or torque tube. Those setups need the correct replacement parts, and guessing leads to a door that won’t balance. Whether you have Amarr, Wayne Dalton, or any other make on your door, we can help.
Signs You Need Garage Door Spring Repair Right Now
- A loud bang from the garage. That sound is usually a torsion spring snapping. The door may still be closed, but it’s now dead weight, and running the opener risks burning out the motor.
- The door opens a few inches and stops. The opener is trying to lift a door the springs are no longer helping with. Stop using it and call before the opener gears strip.
- A visible gap in the spring coil. Look at the torsion spring above the door: a clean break shows as a gap about the width of a finger. Don’t try to wind or unwind it yourself; that’s the highest-risk repair in the trade.
- The door feels extremely heavy when you lift it by hand. A balanced door lifts with one hand. If it takes real effort, the springs have lost tension and the opener is doing work it wasn’t built for.
- The door drifts down or won’t stay open halfway. This points to a tension problem rather than a break, and it’s an early warning that a spring is on its way out.
Our Garage Door Spring Repair Process – Step by Step
- 1
Phone diagnosis. We ask what the door is doing and whether you heard a bang, so we arrive with the likely parts in mind. That saves a second visit on most spring jobs.
- 2
On-site safety check. Before any work, we secure the door, check the cables and drums for damage, and confirm the spring is fully relaxed. High-tension springs store enough energy to injure someone badly, so this step isn’t skipped.
- 3
Measurement and quote. We measure wire gauge, inside diameter, and length, then give you a written price before anything is replaced. You’ll know the number before we start.
- 4
Replacement. We install the new spring or springs, fit safety cables where they’re missing, and wind to the correct tension using proper winding bars. A matched pair is replaced together so the door stays balanced.
- 5
Balance and test. We cycle the door several times, check the balance point, test the opener’s force settings, and confirm the safety reverse works. You get a walkthrough of what we did before we leave.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Garage Door Spring Repair Cost in Bloomington?
A typical spring repair in Bloomington runs $180 – $340 for one spring, depending on the spring type, the door’s weight, and whether cables or drums need attention too. If your door has a matched pair, both springs are usually replaced together, so a pair costs about twice that range. Here’s how the common jobs break down:
| Service | Typical Estimated Range |
|---|---|
| Spring repair (one spring) | $180 – $340 |
| Matched pair of springs | About twice the single-spring range |
| Cable repair | $130 – $250 |
| Track realignment | $120 – $240 |
| Roller replacement | $110 – $220 |
What moves the price: torsion versus extension springs, the door’s size and weight, how many springs need replacing, and whether the cables were damaged when the spring let go. To avoid overpaying, get the quote in writing before work starts and make sure it covers the spring, the labor, and a balance test. Our estimates are free, and the written estimate sets the final price, so the number you agree to is the number you pay.
Garage Door Spring Repair Near Bloomington – Our Service Area
We cover Bloomington and the surrounding south-metro communities, including garage door spring repair in Savage, Prior Lake, Lakeville, Chanhassen, Farmington, Chaska, Orono, Victoria, Mound, Richfield, and Edina. Dispatch runs from 7am to 7pm, Sunday through Friday, and most spring calls in Bloomington are handled the same day. For nearby cities like Richfield and Edina, timing is similar; farther out toward Victoria or Mound, call early in the day and we’ll book the first opening. We also handle garage door spring repair in Prior Lake when a snapped spring leaves a door stuck.
Serving Bloomington, MN – Our Local Coverage Area
We serve Bloomington and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Garage Door Spring Repair in Bloomington
Garage door spring repair is the replacement or adjustment of the springs that counterbalance your door’s weight. Torsion springs sit above the door and extension springs run along the side tracks, and both take the load so your opener only has to guide the door. When a spring fails, the door becomes dangerously heavy or won’t open at all. We replace the failed spring, check the cables and drums, and balance the door before we leave.
Most single-spring replacements take about an hour on site once we’ve confirmed the diagnosis. A matched pair or a job with cable damage can run closer to two hours. Because we ask diagnostic questions on the phone, we usually arrive with the right parts and avoid a second trip. If you call early enough, we can often complete the repair the same day in Bloomington.
A typical single-spring repair in Bloomington runs $180 – $340, and a matched pair costs about twice that. The exact number depends on spring type, door weight, and whether cables need replacing. We quote the price in writing before any work starts, and that written estimate sets the final price. Call (855) 904-7314 for an exact quote – estimates are free.
Yes, we service Genie, Clopay, Amarr, and Wayne Dalton equipment, along with other major makes. Spring systems vary by brand and model, and the wrong spring weight will leave a door unbalanced or put extra strain on the opener. We match the replacement to your specific door. If you’re unsure what’s on your door, tell us what you can see and we’ll sort it out on arrival.
Same-day repair is often available in Bloomington, especially when you call early in the day. Our dispatch hours are 7am to 7pm, Sunday through Friday, and we’re closed Saturday. We answer 24/7, so a call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (855) 904-7314 and we’ll find the soonest slot.
We stand behind our spring work, and replacement springs are covered against defects. The details depend on the spring type and the job, so we’ll explain the coverage on your written estimate before work begins. A properly matched spring on a balanced door is the difference between one repair and a repeat call. Ask us about the warranty on your specific job.
Clear the garage floor around the door and stairs so the technician has room to work safely. Stop using the opener if the spring is broken; lifting a dead-weight door can strip the opener gears and add cost. Tell us on the phone whether the door is stuck open or closed, since that changes how we approach the job. Then just leave the rest to us. Call (855) 904-7314 to book it.
Schedule Your Garage Door Spring Repair Service in Bloomington Today
A broken spring won’t fix itself, and using the door with a failed spring can damage the opener too. Call (855) 904-7314 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday, and same-day repair is often possible in Bloomington. You’ll get an upfront written price before any work starts, and spring replacement done safely, by trained hands. Whether it’s Genie, Clopay, Amarr, or Wayne Dalton on your door, no matter what brand is on your door or opener, we can help.
Written by the team at Bloomington Garage Door Repair Pros.